⎝⎛优德w88体育网⎞⎠

Unfortunately, because your browser version is too low to get the best browsing experience, it is recommended to download and install Google Chrome!

Daily maintenance methods of smart greenhouses (middle)-[Xinwu]

来自: 成都鑫芯电子科技有限公司 浏览次数:1966 2015-11-24From : Chengdu Xinxin Electronic Technology Co., Ltd.Browse Times: 1966

智能温室大棚的维护

The control equipment in the intelligent greenhouse control system is a key part of the entire control. Of course, if the maintenance of the control equipment is not performed well, the life of the equipment will be seriously shortened , and the misinterpretation of the control instructions by the control equipment will cause the control to fail. 示大家做好以下防护措施。 Therefore, in the usual equipment maintenance, Xinxin IOT experts remind everyone to do the following protective measures.

3. Maintenance and troubleshooting of window switch system and curtain switch system

1.Maintenance of window switch system

(1). Regularly check the lubricant in the reducer, and replace the lubricant in the reducer all once a year.

(2). The gear rack of the windowing system should be regularly maintained and lubricated to reduce the power consumption and load of the motor.

(3). Regularly check the condition of the limit switch of the motor, and correct the deviation in time to avoid excessive error causing damage to the window.

(4). Regularly check the opening and closing of the windows, and check whether the opening or closing is not caused due to the working error of the motor.

(5). When the motor is running, if abnormal noise or sound of jamming occurs, the motor should be stopped in time and the motor should be inspected and repaired.

(6). If the seal of the window is not good enough, the seal should be replaced in time.

(7). On snowy days, the windows should be closed in time and the snow above should be cleared.

2. Maintenance of curtain switch system

(1). Regularly check the lubricant in the reducer, and replace the lubricant in the reducer all once a year.

(2). Roller curtains and curtain gears and steel wires of the curtain system should be regularly lubricated to avoid motor damage or wire breakage due to too much friction.

(3). Regularly check the roller shutter limit switch to avoid damage to curtains or other shading equipment.

(4). During the operation of the motor, if abnormal noise or sound of jamming occurs, the motor should be stopped in time and the motor should be inspected and repaired.

(5). The curtain should be rolled up in high wind and snow to avoid equipment damage caused by high wind and snow.

(6). If the curtain gets wet, dry it in time.

3.Solutions for common faults

(1) If the curtain is not stable when it is rolled up and lowered, it is necessary to readjust the connection between the push rod and the guide rod and the speed of the motor, so that it can be rolled up and lowered smoothly and evenly.

(2) If the curtain is still drooping or not completely collected when it is stowed, check whether the trailing line is loose or the motor limit is cheap . Generally, tighten the curtain line and reset the motor limit switch can.

(3) If the curtain is wrinkled, check whether the curtain is damaged or the curtain at both ends of the driving of the roller is loose. If so, repair and replacement or drive rod calibration should be carried out in time .

(4) Always pay attention to the daily weather forecast, and gather out the shade when it encounters heavy snow or wind.

4. Maintenance of fans in greenhouses

1. Be sure to pay attention to the working voltage of the fan during the use of the fan, see the various labels on the nameplate, and the voltage deviation should not exceed 10% of the rated voltage.

2. If the fan has not been used for a long time, before restarting the use, you should thoroughly check the fan circuit and the condition of the fan to see if the connection between the fan blade and the rotating shaft is firm. You should test the machine first before you can work for a long time.

3. The fan should also add lubricant regularly.

4. Regularly clean the dust, dirt and other impurities on the fan blades to keep the fan blades dry and clean. Prevent the fan from being rusted.

5. Maintenance of the fan should be performed after the power is cut off to avoid causing casualties.

6. During the operation of the fan, you should always check whether the rotation of the fan is stable, whether the fan blades are vibrating, and whether the current, voltage and power of the motor are normal. 除故障之后才能继续进行工作。 If fan blades or fans are found to have abnormal vibrations, shocks, excessive current or too small current, they should be stopped and checked immediately, and work can be continued only after troubleshooting.


November 24, 2015

Chengdu Xinxin Electronic Technology Co., Ltd. Editorial Department

Editor: Little Devil in Gourd


Scan to access mobile
天天电玩城 七乐彩 欢乐拼三张 星力捕鱼